Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
What're your thoughts about How to Install a Bathtub?
Mounting a tub isn't exactly rocket science, however it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult task. If the old bathtub is readily obtainable, the job can move easily; if you have to open a wall surface to remove the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the job as well as are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will aid you set up a new tub in your shower room if you have actually currently purchased a new bathtub as well as don't need to transform the plan of your previous water supply pipelines.
Your tools and product checklist must consist of the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The procedure of removing the existing faucets can be rather troublesome as a result of the restricted access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in place between the faucet and also the sink. Protect the tap in place with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind must be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub until the level reviews degree.
To mount taps, fit the bottom of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water supply as well as inspect all joints and also new pipework for leaks and tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and also the regular outlet for leakages.
Lastly, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the tub must wait up until the bathtub has been made use of at least when as this will resolve it right into its final setting.
Planning for the Installment
Firstly, the sustaining frame provided with the bath must be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing problems with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the activity experienced when the tub remains in use. The sealant can fracture fairly early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very excited about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you enjoyed our post. Appreciated our entry? Please share it. Let others check it out. I take joy in reading our article about How to Install a Bathtub Yourself.
Toilet overflow? Call us! Report this page